Модуль аналогового ввода-вывода EM 134, 3 аналоговых входа 12 бит (напряжение, ток), 1 аналоговый вход 12 бит (Pt, Ni, cопротивление), 2 аналоговых выхода 12 бит (напряжение, ток)
|
Наименование
|
Модуль аналоговых входов/выходов 3 AI+Pt100+2 AO, мультивходы |
|
Тип
|
VIPA134-4EE00 |
|
Габаритные размеры, В х Ш х Г, мм
|
101.6 mm x 76 mm x 48 mm |
|
Температура окружающей среды
|
0 °C .. 60 °C |
|
Серия
|
100V |
|
Количество входов
|
4 |
|
Количество выходов
|
2 |
|
Тип входного сигнала
|
3хAI U/I, 1x Pt, Ni, R |
|
Тип выходного сигнала
|
U/I |
Structure
| Position X1 | Position X2 | Position X3 | Position X4 |
| AI 3x12Bit | not used |
AI 1x12Bit |
not used |
Status monitor pin assignment
| Pin assignment | ||
 |
|
1x Analog input (Pt, Ni, R)
2x Analog outputs (U/I)
| LED | Description | Pin assignment | |||
| L+ |
LED (green) |
 |
|
||
| SF |
Sum error LED (red) |
Order no. |
134-4EE00 |
| Type | EM 134 |
General information |
|
| Note | - |
| Features | 3 inputs U/I 1 input Pt, Ni, R 2 outputs U/I Configurable |
Current consumption/power loss |
|
| Current consumption from backplane bus | 70 mA |
| Power loss | 2 W |
Technical data analog inputs |
|
| Number of inputs | 4 |
| Cable length, shielded | - |
| Rated load voltage | DC 24 V |
| Reverse polarity protection of rated load voltage |  |
| Current consumption from load voltage L+ (without load) | 55 mA |
| Voltage inputs | |
| Min. input resistance (voltage range) | 120 kΩ |
| Input voltage ranges | +1 V ... +5 V 0 V ... +10 V -10 V ... +10 V |
| Operational limit of voltage ranges | +/-0.3% ... +/-0.7% |
| Operational limit of voltage ranges with SFU | - |
| Basic error limit voltage ranges | +/-0.2% ... +/-0.5% |
| Basic error limit voltage ranges with SFU | - |
| Destruction limit current | - |
| Current inputs | |
| Max. input resistance (current range) | 110 Ω |
| Input current ranges | +4 mA ... +20 mA -20 mA ... +20 mA 0 mA ... +20 mA |
| Operational limit of current ranges | +/-0.3% ... +/-0.8% |
| Operational limit of current ranges with SFU | - |
| Basic error limit current ranges | +/-0.2% ... +/-0.5% |
| Radical error limit current ranges with SFU | - |
| Destruction limit current inputs (electrical current) | - |
| Destruction limit current inputs (voltage) | - |
| Resistance inputs | |
| Resistance ranges | 0 ... 600 Ohm 0 ... 3000 Ohm |
| Operational limit of resistor ranges | +/-0.4% |
| Operational limit of resistor ranges with SFU | - |
| Basic error limit | +/-0.2% |
| Basic error limit with SFU | - |
| Destruction limit resistance inputs | - |
| Resistance thermometer inputs | |
| Resistance thermometer ranges | Pt100 Pt1000 Ni100 Ni1000 |
| Operational limit of resistance thermometer ranges | +/-0.6% ... +/-1.0% |
| Operational limit of resistance thermometer ranges with SFU | - |
| Basic error limit thermoresistor ranges | +/-0.4% ... +/-0.5% |
| Basic error limit thermoresistor ranges with SFU | - |
| Destruction limit resistance thermometer inputs | - |
| Thermocouple inputs | - |
| Thermocouple ranges | - |
| Operational limit of thermocouple ranges | - |
| Operational limit of thermocouple ranges with SFU | - |
| Basic error limit thermoelement ranges | - |
| Basic error limit thermoelement ranges with SFU | - |
| Destruction limit thermocouple inputs | - |
| Programmable temperature compensation | - |
| External temperature compensation | - |
| Internal temperature compensation | - |
| Internal temperature compensation | - |
| Technical unit of temperature measurement | - |
| Resolution in bit | 12 |
| Measurement principle | successive approximation |
| Basic conversion time | 3.2 ms / channel |
| Noise suppression for frequency | 50 Hz, 60 Hz, 400 Hz |
| Initial data size | 8 Byte |
Technical data analog outputs |
|
| Number of outputs | 2 |
| Cable length, shielded | - |
| Rated load voltage | DC 24 V |
| Reverse polarity protection of rated load voltage | |
| Current consumption from load voltage L+ (without load) | 55 mA |
| Voltage output short-circuit protection | |
| Voltage outputs | |
| Min. load resistance (voltage range) | 1 kΩ |
| Max. capacitive load (current range) | 1 µF |
| Max. inductive load (current range) | 30 mA |
| Output voltage ranges | -10 V ... +10 V +1 V ... +5 V 0 V ... +10 V |
| Operational limit of voltage ranges | +/-0.4% ... +/-0.8% |
| Basic error limit voltage ranges | +/-0.2% ... +/-0.4% |
| Destruction limit against external applied voltage | - |
| Current outputs | |
| Max. in load resistance (current range) | 500 Ω |
| Max. inductive load (current range) | 10 mH |
| Max. inductive load (current range) | 15 V |
| Output current ranges | 0 mA ... +20 mA +4 mA ... +20 mA -20 mA ... +20 mA |
| Operational limit of current ranges | +/-0.3% ... +/-0.8% |
| Basic error limit current ranges | +/-0.2% ... +/-0.5% |
| Destruction limit against external applied voltage | - |
| Settling time for ohmic load | 0.5 ms |
| Settling time for capacitive load | 1 ms |
| Settling time for inductive load | 1 ms |
| Resolution in bit | 12 |
| Conversion time | 1.2 ms / channel |
| Substitute value can be applied | yes |
| Output data size | 4 Byte |
Status information, alarms, diagnostics |
|
| Status display | none |
| Interrupts | yes |
| Process alarm | no |
| Diagnostic interrupt | yes, parameterizable |
| Diagnostic functions | yes |
| Diagnostics information read-out | possible |
| Supply voltage display | green LED |
| Group error display | red SF LED |
| Channel error display | none |
Isolation |
|
| Between channels | - |
| Between channels of groups to | - |
| Between channels and backplane bus | |
| Between channels and power supply | |
| Max. potential difference between circuits | - |
| Max. potential difference between inputs (Ucm) | DC 11 V |
| Max. potential difference between Mana and Mintern (Uiso) | DC 75 V/ AC 60 V |
| Max. potential difference between inputs and Mana (Ucm) | DC 11 V |
| Max. potential difference between inputs and Mintern (Uiso) | DC 75 V/ AC 60 V |
| Max. potential difference between Mintern and outputs | - |
| Insulation tested with | DC 500 V |
Datasizes |
|
| Input bytes | 8 |
| Output bytes | 4 |
| Parameter bytes | 18 |
| Diagnostic bytes | 12 |
Housing |
|
| Material | PPE / PA 6.6 |
| Mounting | Profile rail 35 mm |
Mechanical data |
|
| Dimensions (WxHxD) | 101.6 mm x 76 mm x 48 mm |
| Weight | 230 g |
Environmental conditions |
|
| Operating temperature | 0 °C to 60 °C |
| Storage temperature | -25 °C to 70 °C |
Certifications |
|
| UL508 certification | yes |
| Order no. | Name/Description | |
|---|---|---|
|
134-4EE00 |
EM 134 - Expansion module, analog 3 inputs U/I 1 input Pt, Ni, R 2 outputs U/I Configurable |
 [Datasheet] [Manual] |
г. Алматы, Ауэзовский район
ул. Толе Би 302, Литер "Д"
офис № 205
+7 (727) 268-0321
+7 (701) 082-9486
+7 (707) 493-7210
+7 (727) 268-0321
info@controllink.kz
